15921758826
15921758826
Shanghai Weitao automation equipment Co., Ltd
Contact person: Mr. Lu
Tel: 15921758826
Address: 2312 Weiqing East Road, Shanyang Town, Jinshan District, Shanghai
Brief introduction of the soup ironing sublimation Fastness meter
Project standard
AATCC 133-2013AATCC 117-2004ISO 105 x11-1994, JIS L0850-1994ISO 105 p01-1993GB /T 6152-1997m &S C13M&S P10
Upper body heat, top and bottom plate parallelism between the upper and lower double good heat transfer heat the upper, and parallelism between tablet good smooth parallel plate with fine control electrical heating system with fine control electric heating system of smooth and parallel plate (heat can only from the top plate is passed to the sample) independent temperature control device, double-side heating up and down
Pressure to 40 + 10 g/kpa4 cm24 + 1 + 1 kpa kpa4 kpa4 + 1 + 1
Temperature 110±2 ° C 150±2 ° C 200±2 ° C 150±2 ° C 180±2 ° C 110±2 ° C 150±2 ° C 150±2 ° C 150±2 ° C 110±2 ° C Precision ±2 ° C
Asbestos sheet thickness requirement /3mm-6mm thick /3mm-6mm thick
Cushioned wool flannel with a mass of 260g/m2 per unit area,3mm thick, or other wool fabric or wool disc with a mass of 260g/m2 per unit area,3mm thick, or other wool fabric or wool disc with a mass of 260g/m2 per unit area
Bleached cotton fabric per unit area mass 100g/ M2-130g /m2 Undyed and unmercerized Single fiber fabric per unit area mass 100g/m2-130g/m2 undyed and unmercerized single fiber fabric per unit area mass 100g/m2-130g/m2 undyed and unmercerized single fiber fabric per unit area mass ISO 105-F10 undyed and unmercerized single fiber fabric per unit area mass ISO 105-F01:08 Undyed and unmercerized single fiber fabric per unit area mass 100g/m2-130g/m2 undyed and unmercerized single fiber fabric per unit area mass ISO 105-F01:08 Undyed and unmercerized single fiber fabric per unit area mass 100g/m2-130g/m2 undyed and unmercerized single fiber fabric per unit area mass
Cotton/multi-fiber fabrics ISO 105-F:1985: F02 GB 7565
Number of sample blocks required: 223331(20×10cm)1(20×20cm)
Test time: 15S30S15S30S15S30S30s
Used to test the appearance quality of yarn and dyeing fabric.
Appearance quality usually refers to yarn dryness, yarn defects, dyeing fabric dyeing fastness, etc.
There are three methods to check the evenness and defects of yarn: eye evaluation method, weighing method and instrument method
Bill of materials
When you open the package, please check the following materials:
Color fastness tester to ironing sublimation
Two 230V50HZ power lines or one 115V60HZ power line
The fuse
It may also include as needed
baize
Heat insulation slices
Cotton pad
Discoloration and contamination rating grey CARDS
Scale (Dimensional stability test)
The installation
After unpacking, place the instrument on a horizontal plane.
The room should be clean and well ventilated.
Do not install equipment in toxic environment.
Plug the power connector into the back of the instrument and switch on the power to ensure grounding.
Operation method
Sample placement specification
Instrument preheating
A variety of standard tests can be performed using a sublimation/ironing fastness meter with precise temperature control.
The upper and lower plates shall be preheated before the test to ensure that the temperature is stable and meets the standard requirements.
Install the power cord, turn on the toggle switch, light up the temperature control meter and timer, set the test temperature according to the test content, close the upper cover plate and start heating the upper and lower plates.
Dry heat/sublimation resistance test
1. Before the test, select and set the test time (usually 30s) and test temperature according to the standard and sample type, and preheat the machine.
2. According to the requirements of the test standard, the cut dry sample is prepared according to the standard method (in the standard test, in order to ensure the accurate pressure above the fabric, in the multi-sample test, please strictly follow the specification of the sample placement in the instructions)
3. After the machine is preheated to the set temperature, open the upper panel and press the timer switch.
4. Place the prepared sample into the panel to ensure the smooth surface, and the timer will start automatically after covering the panel.
5. After reaching the set time, the buzzer will ring, close the timer switch, open the upper cover plate and take out the sample.
6. Repeat steps 2-5 if you need to repeat the test
7. Compare the test sample with the corresponding grey card to evaluate the color change grade;
The stain grade was obtained by comparing the padded cotton fabric with the grey card.
Color fastness to hot pressing/ironing
To test the color change and color transfer degree of the fabric after hot pressing, the hot pressing fabric can be dry, hygroscopic and wet three kinds, usually determined by the final use of the fabric.
Before the test, select and set the test time (usually 15s) and test temperature according to the standard and sample type, and preheat the machine.
Note: Do not turn on the timer switch when the instrument is preheating, otherwise the timer will start automatically after the cover is closed.
Stack asbestos sheets, flannel, dried or wetted samples and white cotton linings as required according to test standards.
After the machine is preheated to the set temperature, open the upper panel and press the timer switch.
Place the stacked samples in one time to ensure the smooth surface. The timer will start automatically after covering the upper panel.
After reaching the set time, the buzzer will sound, turn off the timer switch, open the upper cover plate and take out the sample.
To ensure temperature stability, if the test interval is long, please close the upper cover plate.
Note the high temperature burn during the test
Repeat steps 2-5 if you need to repeat the test.
Compare the test sample with the corresponding grey card to evaluate the color change grade.
The stain grade was obtained by comparing the white cotton cloth with the grey card.
Dimensional stability test
The stability of the fabric at melting temperature was evaluated by comparing the length and width of the fabric before and after hot pressing at a certain temperature.
The following is an example of M&S P10 standard to introduce the test method.
Cut the fabric to 20×20cm.
Determine the test temperature according to the heat-resisting property of the fabric, and set the test temperature for 30s.
After the machine is preheated to the set temperature, open the upper panel and press the timer switch.
Put the sample in, make sure it is flat, and the timer will start automatically after covering the upper panel.
After reaching the set time, the buzzer will sound, turn off the timer switch, open the upper cover plate and take out the sample.
The dimension of the fabric after the test is measured with a scale precision of 1 mm, and the rate of dimension change is calculated.
Repeat steps 3-6 if you need to repeat the test.
Sincerity Smart
maintenance
This instrument requires only simple maintenance.
To ensure the test environment is clean and dust-free, especially the residual cotton wool on the upper and lower panel of the instrument after the test.
If you need to replace the aging heating equipment, please contact our company xi to purchase and install.
It is mainly used for testing the high temperature resistance of all kinds of colored textiles, the heat-resisting pressure of the color of textiles and the processing ability of hot roller.
It can also be used to detect the quality of printing and dyeing products.
Lfy-301a and LFY-301B are three-station and simplex positions.
1. Three stations can be used to test three samples at the same time.
2. Each station is equipped with independent PID self-setting temperature controller.
3. Set temperature and test temperature can be displayed at all stations.
4. Each station has an independent time controller
Temperature control range: room temperature ~ 250℃
2. Temperature control accuracy: ±1℃
3. Test time: 1 second ~ 99.99±0.1 second
4. Test pressure: 4KPa±1Kpa
5. Heating power: 400W/ each station
6. Power supply: AC220V, 50Hz 1.2kW
GB/T 6152-1997 Colour fastness test for Textiles Colour Fastness to heat pressure
Color Fastness test to Dry Heat (except hot pressing) for Textiles
ISO105/ p01-1989 test method for colour fastness to dry heat (sublimation) of textiles
AATCC 133-2004
Founded in 2011, Shanghai Huitao is a team of experienced engineers and emerging design experts. The company focuses on R & D, design and production of high quality laboratory instruments for textile testing. Headquartered in Shanghai, the company provides high-quality testing instruments and high-quality professional services for companies, academic research institutions and testing institutions of various countries.
Shanghai Huitao continuously launched products to meet the experimental needs of the textile industry. It has advanced microclimate comfort test equipment, such as thermal manikin, thermal and humidity resistance tester, MMT and other test equipment. Meanwhile, it also provides air permeability tester, hydrostatic pressure tester and thermal protective clothing performance test equipment required for new product development. In addition, we have developed and produced many basic textile testing instruments, including washing color fastness tester, fabric abrasion tester, pilling tester, rubbing color fastness tester, ironing fastness tester and perspiration color fastness tester. These high-quality products are widely used in textile testing field. In order to meet the experimental needs of users, we also provide you with innovative and practical testing instruments. The products include fiber tester, yarn tester, fabric tester, carpet tester, geotextile tester and other related testing equipment.
The company sells our products through distributed distribution partners who provide high-quality products, services and support to our customers all over the world. All the products are in line with international quality standards and specifications, and can perform outstanding and accurate product performance.
