Welcome toShanghai Weitao automation equipment Co., Ltdwebsite!

15921758826

Hot search:

Moisture resistant microbial penetration tester

product

Hot news

contact us

Shanghai Weitao automation equipment Co., Ltd

Contact person: Mr. Lu

Tel: 15921758826

Address: 2312 Weiqing East Road, Shanyang Town, Jinshan District, Shanghai


circle sample cutter

circle sample cutter
Visits : 0
Editing time : 2020-10-21
Detailed introduction:

Disc sampler is suitable for cutting circular samples of wool, cotton, chemical fiber and knitting fabrics.




essential information




Chinese name




circle sample cutter




Cut round samples of various woolen fabrics




Size: Φ 132 × 130mm




Shear thickness




4mm





Main technical specifications the instrument is suitable for cutting circular samples of various wool, cotton, chemical fiber and knitting fabrics




Sample area: 100cm2, thickness of cut fabric: 4mm




Instrument size: Φ 132 × 130mm




No advertising information is adulterated. It's just a regular promotion. Thank you!




usage method:




Lay the fabric to be cut on the rubber pad, place the disc sampler on the fabric, pull out the locking device on the sampler, rotate it about 90 degrees, hold the outer cover with one hand, hold the corrugated hand wheel with the other hand, and apply certain pressure, and then rotate the corrugated hand wheel clockwise (the angle is greater than 90 degrees), and then the circular sample can be cut. After the sampler is used, the locking device is rotated to the original position, so that the blade can not be exposed to avoid injury to hands and other objects.




Structure and adjustment:




The cutting blade is a double-sided blade with four equal parts, which are round and four evenly distributed. The blade can be replaced. The specific operation is as follows: loosen the cross screw (there are four screws on each piece), remove the blade pressing plate and sampling blade, replace with a new blade, press on the blade pressure plate, pay attention to make the blade edge clockwise, and make the four blade edges in the same plane, and then tighten the cross screw.




There are straight lines on the bottom of the instrument, which are used to fix the sample for cutting and prevent the sample from slipping.




matters needing attention:




The blade edge of the instrument is sharp. Do not put your hand on the bottom to avoid damage.




The sample should be cut on the rubber pad. When the instrument is not in use, it should be cleaned and placed in the instrument box to avoid damage.




It can also be equipped with professional high-precision electronic balance to accurately weigh out grams. It is suitable for all kinds of textile, cloth art, printing and dyeing, sampling and other factories and foreign trade companies.






The quality assurance of the instrument for 12 months from the date of first use or 15 months from the date of delivery shall be based on the first occurrence. The instrument has passed the inspection and test, so there are no material and process defects. This guarantee is in lieu of any other warranty, express or implied. In any event, it shall be liable and liable for any special or indirect damages caused by breach of this warranty.






The responsibility is limited to the repair or replacement of any defective parts produced during on-board and factory delivery. There will be no warranty for damage to instruments or components caused by abuse, improper use, accident, change, neglect, unauthorized maintenance or installation. Zui has the final decision on the defect identification and the causes.






After the parts are repaired or replaced, the warranty within 6 months from the original warranty period or the date of spontaneous loan shall continue to be valid according to the longer warranty period.






It reserves the right to make changes and improvements to its products, but has no obligation to carry out improvement and installation on the products already produced.




1.3 warranty of components






The parts and materials supplied have been inspected and tested to ensure that they are free from defects and defects and will work properly when they are properly installed and operated on the manufactured instruments. The warranty period of parts (excluding consumable parts such as light source, optical element, friction cloth, etc.) is 6 months from the delivery date.






This guarantee is in lieu of any other warranty, express or implied. In any event, it shall be liable and liable for any special or indirect damages caused by breach of this warranty.






The responsibility is limited to the repair or replacement of any defective parts produced during on-board and factory delivery. There will be no warranty for damage to components caused by abuse, improper use, accident, change, neglect, unauthorized repair or installation. Zui has the final decision on the defect identification and the causes.






It reserves the right to make changes and improvements to its products, but has no obligation to carry out improvement and installation on the products already produced.




1.4 operating environment






The instrument is used in residential, commercial and light industrial environments in accordance with BS EN 50081-1 and BS EN 50082-1




1.5 climate environment






It has the right to change and improve its products, but has no obligation to carry out improvement and installation on the products already produced.




The instrument operates under the following conditions:




Altitude < 2000m




Operating temperature: 13 ~ 30 ℃ (56 ~ 86 ℃), relative humidity 25 ~ 75%




Storage temperature: 10-43 ℃ (50-110 f), relative humidity 20-80%






The instrument can be placed in the operation environment required by the standard, so as to ensure the operation consistency between the sample humidity adjustment and the actual wear test.




1.6 electrical information






The electrical requirements of this instrument comply with en 61010-1:2001, measurement, control and laboratory use.




1.7 installation type and pollution level






Installation category I






Pollution level 1




1.8 warning signs


Founded in 2011, Shanghai Huitao is a team of experienced engineers and emerging design experts. The company focuses on R & D, design and production of high quality laboratory instruments for textile testing. Headquartered in Shanghai, the company provides high-quality testing instruments and high-quality professional services for companies, academic research institutions and testing institutions of various countries.

Shanghai Huitao continuously launched products to meet the experimental needs of the textile industry. It has advanced microclimate comfort test equipment, such as thermal manikin, thermal and humidity resistance tester, MMT and other test equipment. Meanwhile, it also provides air permeability tester, hydrostatic pressure tester and thermal protective clothing performance test equipment required for new product development. In addition, we have developed and produced many basic textile testing instruments, including washing color fastness tester, fabric abrasion tester, pilling tester, rubbing color fastness tester, ironing fastness tester and perspiration color fastness tester. These high-quality products are widely used in textile testing field. In order to meet the experimental needs of users, we also provide you with innovative and practical testing instruments. The products include fiber tester, yarn tester, fabric tester, carpet tester, geotextile tester and other related testing equipment.

The company sells our products through distributed distribution partners who provide high-quality products, services and support to our customers all over the world. All the products are in line with international quality standards and specifications, and can perform outstanding and accurate product performance.


15921758826